Updated:
11 May, 2007
KQLZ - Click to Rock
I actually have lots of things I build or fix or change in some way that I could put up here. I just don't have pictures of them... So this page is somewhat incomplete. I don't know if it ever will be... but here's where I have for now.
If you want to see the kind of stuff I did for the Univ of IL (Champaign/Urbana), click this link.
Sign the GuestBook while you're here!
| Liquid Cooled Cup Holder for my Jeep (Dec. 2006) It's not finished YET! |
The base cup chamber design...;)
;)
;)
;)
;)
Cup chamber v1 design: I didn't like it... ;)
;)
;)
;)
;)
;)
;)
;)
Cup chamber v2 design: This is what I wish would FIT into the car. ;)
Cup chamber v3 design: This is what will really go into the car. (no pics yet up here) Coolant Reservior: The "tubing only" designs require coolent to be stored and air bubbles to go someplace... so. (no pics yet up here) The LED/Temp Sensor Tray. The last image is a ~4MB Movie! ;)
;)
The Cooling unit. Peltier/Fan/Electronics to make it all happen! ;)
;)
;)
;)
;)
;)
;)
;)
|
|---|---|
| Linksys WAP11 In a box (Mar. 2006) |
;)
;)
|
| CerfBoard255 1Mx16 SRAM PCB (Jul. 2005) |
;)
;)
;)
;)
|
| CerfBoard255 Signal Breakout PCB (Jun. 2005) |
Coming soon. I need to take some pics... |
| Jeep Wrangler Amplifier Deck (Apr. 2005) |
;)
;)
;)
|
| PIC Based Dual Axis Accelerometer Display w/6 Axis capability (Dec. 2004) |
Coming soon. It's built, the software's still in progress. |
| Atari Tempest ROM4 & Tempest Tubes (Sep, 2003) |
;)
;)
Ok, this was so easy it's not even funny - but I thought I would list it for those who want to "do it themselves". NOTE: MOUNT THE SWITCH OFF THE END OF PIN 1! I mounted it
towards the bottom and the switch bumps into the large connector at the edge of the board.
|
| PIC Based 4-Temp / 2-Voltage Monitor (Sep, 2002) |
;)
;)
;)
;)
;)
;)
;)
My first version of this was LCD based. I changed my mind so I could hook the unit to a computer to log the temps every so many minutes. The screen shot on the left shows the raw output as seen from a direct serial connection. The shot on the right is after I pass it through some TCL code to make it more log-file friendly. I suppose I could have formatted the output from the sensor directly into what the TCL code does.. but then the sensor isn't as fancy. So... anyway - if anyone wants the 'C' code, feel free to send me an email. |
| Empeg LED Modifications (Sep, 2002) |
;)
;)
The empeg actually has room for T-1 sized LED's inside the push-switches. Just add the R-Pak (I used 500ohms for a total current of 10mA @ 5VDC. Now I just need to get the transluscent buttons from Brian's Empeg Button Page. |
| Empeg Fan Kit (Aug, 2002) |
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
The 1st pic is actual temp controller. The LCD display is just the mPU that's going to set the chip. This was just an exercise to show me the chip correctly operating. After that, you can see where I put the unit and the pads near the power connector where I connected to +12vdc. This mod is supported by HiJack for the empeg which can be found at http://empeg-hijack.sourceforge.net/. Get version 3.04 or later. The schematic is located here. Enjoy! |
| "Empeg" MP3 Stereo for the Jeep (Feb-Mar, 2001) |
;)
;)
;)
;)
;)
One of the coolest gizmo's you can put in your car... unfortunately, no longer made. But check 'em out at www.riocar.org or empegbbs.net. |
| Custom Made Jeep Speakers for my '97 Jeep Wrangler (7/3/99) |
;)
;)
;)
I made these from Radio Shack 6x9 Carpet Covered Cabinets, Jensen 120Watt 2way (Whizzer) Speakers, 1" U-Bolts, some Tie-Down
straps and a sections of, yes it really is, conduit from Home Depot painted black courtesy of
Rust-Oleum. They are wired up to the Amps show above.
|
| The LiteBrite Board ('97) |
;)
;)
;)
This is one of my favorite nonsense gizmo's right now. It's run by a set of TCL programs on my Unix
Server that display, Time/Date, Weather, Local Airport Data, APC UPS Data, CallerID and completed
SETI@Home Work Units.
|
| PIC Programmer (for the project above) in a custom case. (early '99) |
;)
;)
|
| PIC Based 4-Line Temperature Display (early '99?) |
;)
;)
(taught myself 'C' on this project) Here ya go Marty! |
| FM Transmitter
WBEN as it were (ho ho ho) (early '99?) |
;)
;)
;)
;) This was made with an MPX96 available from North Country Radio by Bill Sheets. A most excellent sounding unit unlike the crap that Ramsey Electronics sells for more money!! Buy the MPX96!! |
| Video Game Conversion Cabinet (Top row is the control panel bottom row is the whole thing) |
;)
;)
;)
;)
;)
;)
;)
;)
|
|
Joust (Arcade Game) Board Set Had to mount and wire. Joy!(Nov.13,99) |
;)
|
|
NTSC Video Sync Splitter (circa 1990) |
;)
(This was a bet as to how many posts I could get on this box)
|
|
Laser Power Supply (circa 1987??) |
;)
;)
|
| Stereo Decoder for TV. (Circa 1986?) |
;)
This went into the Fischer FVH-810 VCR I had... Any TV stations in Stereo would be decoded accordingly. The decoder used a Broadcast FM Stereo Decoding Chip (LM1800) retuned for the 15.75KHz carrier that was used for TV. FM Radio uses 19KHz for it's pilot carrier. |
|
Ben's First Power Supply - 12VDC (circa 1983) |
;)
;)
|
|
Ben's first Atari Accessory (circa 1983) It's a Joystick Port Breakout Box! |
;)
|
|
Your Host: Unresolvable - tsk tsk tsk Your Addr: 38.103.63.57 
|
 © 1999-2008 BenJammin.Net. |